publication venue for
- Chitosan-mediated electrosynthesis of organic–inorganic nanocomposites 2007
- Effect of high strain rate on plastic deformation of a low alloy steel subjected to ballistic impact 2005
- The effect of tempering on low cycle fatigue behavior of Al-2024 2005
- Rapid machining of hardened AISI H13 and D2 moulds, dies and press tools 2003
- High speed end milling of hardened AISI D2 tool steel (∼58 HRC) 2002
- Modelling of hard part machining 2002
- The removal of copper-phase segregation and the subsequent improvement in mechanical properties of cast 319 aluminium alloys by a two-stage solution heat treatment 1995
- Laser machining of free-standing silicon nitride membranes. 318:118001-118001. 2023
- Investigating the microstructural evolution and interfacial morphology of laser- and arc-brazed ZnAlMg coated steel. 316:117943-117943. 2023
- A novel approach to cutting tool edge design based on initial wear stage. 304:117561-117561. 2022
- Improvement of fatigue performance of laser powder bed fusion fabricated IN625 and IN718 superalloys via shot peening. 304:117571-117571. 2022
- Failure behavior of resistance spot welded advanced high strength steel: The role of surface condition and initial microstructure. 299:117370-117370. 2022
- Joining light metals with polymer composites through metal overcasting. 298:117257-117257. 2021
- Corrigendum to “Optimizing weld morphology and mechanical properties of laser welded Al-Si coated 22MnB5 by surface application of colloidal graphite” [J. Mater. Process. Technol. 293 (2021) 117093]. 297:117270-117270. 2021
- Improvement of thermal conductivity of diamond/Al composites by optimization of liquid-solid separation process. 297:117267-117267. 2021
- Electrical discharge surface texturing for enhanced pool boiling heat transfer. 293:117083-117083. 2021
- Optimizing weld morphology and mechanical properties of laser welded Al-Si coated 22MnB5 by surface application of colloidal graphite. 293:117093-117093. 2021
- On the hot embrittlement of continuously-cast and transfer-bar structures in DP600 advanced high-strength steel. 289:116936-116936. 2021
- Occurrence of sub-critical heat affected zone liquid metal embrittlement in joining of advanced high strength steel. 288:116917-116917. 2021
- A Crystal Plasticity Formulation for Simulating the Formability of a Transformation Induced Plasticity Steel. 287:116493-116493. 2021
- Meso-scale modelling of semi-solid deformation in aluminum foundry alloys: Effects of feeding and microstructure on hot tearing susceptibility. 279:116551-116551. 2020
- Effects on tool performance of cutting edge prepared by pressurized air wet abrasive jet machining (PAWAJM). 277:116456-116456. 2020
- Effect of polarization on ripple formation in deep femtosecond laser machined cavities. 271:162-171. 2019
- Effect of runner design on the externally solidified crystals in vacuum die-cast Mg-3.0Nd-0.3Zn-0.6Zr alloy. 267:366-375. 2019
- Comparison of the semi-solid constitutive behaviour of A356 and B206 aluminum foundry alloys. 266:37-45. 2019
- Density and mechanical properties in selective laser melting of Invar 36 and stainless steel 316L. 266:397-420. 2019
- Effect of coating type on microstructure and mechanical behavior of resistance spot welds of thin X626 aluminum sheet to low carbon steel. 264:438-447. 2019
- Friction stir processing of AlSi10Mg parts produced by selective laser melting. 263:308-320. 2019
- Microstructure and mechanical properties of laser welded dissimilar joints between QP and boron alloyed martensitic steels. 259:58-67. 2018
- Dendritic coarsening model for rapid solidification of Ni-superalloy via electrospark deposition. 258:138-143. 2018
- Comparative effects of Al-Si and galvannealed coatings on the properties of resistance spot welded hot stamping steel joints. 236:64-72. 2016
- FE simulations of gas blow forming and prediction of forming limit diagram of AZ31 magnesium sheet. 218:12-22. 2015
- A new method of determining forming limit diagram for sheet materials by gas blow forming. 214:2960-2970. 2014
- Application of foil electrodes for electro-erosion edge honing of complex-shaped carbide inserts. 213:434-443. 2013
- Effects of electrolyte on hardening in laser hole sealing of commercially pure grade 1 titanium. 212:2012-2019. 2012
- Tool wear mechanisms and tool life enhancement in ultra-precision machining of titanium. 212:560-570. 2012
- A macro–micro-multi-level modeling scheme to study the effect of particle distribution on wrap-bendability of AA5754 sheet alloys. 210:1232-1242. 2010
- Studies on the micro-laser spot welding of an NdFeB permanent magnet with a low carbon steel. 210:885-891. 2010
- Electrophoretic deposition of manganese dioxide–carbon nanotube composites. 209:3452-3459. 2009
- Electrodeposition of zinc and composite zinc–yttria stabilized zirconia coatings. 209:2632-2640. 2009
- Electrophoretic deposition of bioactive glass/polymer composite coatings with and without HA nanoparticle inclusions for biomedical applications. 209:1853-1860. 2009
- Electrophoretic deposition of composite hydroxyapatite–chitosan–heparin coatings. 209:1597-1606. 2009
- Investigation of ultrasonic copper wire wedge bonding on Au/Ni plated Cu substrates at ambient temperature. 208:179-186. 2008
- Finite element modeling of electron beam welding of a large complex Al alloy structure by parallel computations. 199:41-48. 2008
- Nano-aluminum-phosphate via a polymerized organic–inorganic complex route. 190:393-396. 2007
- Manganese oxide films for electrochemical supercapacitors. 186:356-361. 2007
- Numerical simulation of the pressure ram forming process. 182:411-417. 2007
- Image processing for machine vision measurement of hot formed parts. 174:1-6. 2006
- Dynamic shear band propagation and failure in AISI 4340 steel. 169:150-155. 2005
- Mathematical modeling and computer simulation of molten aluminum cleansing by the rotating impeller degasser. 168:119-126. 2005
- Dynamic mechanical behavior of pure titanium. 155-156:1889-1892. 2004
- Total hip performance under magnetic field. 153-154:508-513. 2004
- Numerical study on the effect of electrode force in small-scale resistance spot welding. 139:635-641. 2003
- Study of the formation of adiabatic shear bands in steels. 119:234-236. 2001
- Numerical prediction of the limiting draw ratio for aluminum alloy sheet. 100:131-141. 2000
- Temperature measurement when high speed machining hardened mould/die steel. 92-93:293-301. 1999
- Grinding of cemented carbide with electrical spark assistance. 72:61-68. 1997
- Dynamic modeling for the prediction of surface errors in the milling of thin-walled sections. 25:215-228. 1991